The Motorola GR Repeater provides the perfect solution. By making it easy to extend your two-way system to accommodate longer distances, these. NOTE: THIS IS AN ASTRON SLM POWER SUPPLY. (IN THIS CASE, THE “M” STANDS FOR MOTOROLA-. THERE ARE NO METERS ON THIS UNIT). Motorola GR VHF/UHF 40/45Watts Increase the range and capabilities of your mobile and portable radios with the GR repeater. It provides the flexibility.

Author: Kazinos JoJojinn
Country: Spain
Language: English (Spanish)
Genre: Science
Published (Last): 12 December 2010
Pages: 362
PDF File Size: 8.46 Mb
ePub File Size: 13.16 Mb
ISBN: 627-8-28983-584-6
Downloads: 15074
Price: Free* [*Free Regsitration Required]
Uploader: Tugal

The price list note says “UHF If you patch the RSS to allow 32 channels supposedly motorola gr500 repeater can channel steer with five input lines allowing 32 channels To open the radios you will need to remove the two screws motorola gr500 repeater the control panel T15 and the four flat-head screws from the sides T Note that they will vibrate loose in mobile service but this will get you by in a base station environment or until you can locate the proper connector The three channel select lines on a Radius limits you to 8 motorola gr500 repeater channels 1 through 7 plus whatever the front panel has selected – and while it usually stays where you leave it, I don’t count on the front panel selection staying put during a power cycle I also think the kits will work on the Maratrac since the receiver and exciter are basically a 5-pin MaxTrac mounted in the Maratrac chassis.

This is due to the design, and the design follows the laws of physics.

Now mount and solder the new connector. The receiver is in carrier squelch when this pin is floating, and when it is grounded if the channel has PL or DPL programmed the receiver must have the proper PL or DPL to unsquelch motorola gr500 repeater.

Motorola GR Repeater | RADIO TRUNK | Two-Way Radio

Any Motorola prices mentioned on this page or on any page at this web site should be taken only as a rough guideline. The male connector require a unique crimping tool to be installed properly, and they are designed to motorola gr500 repeater only a few types of coaxial cable.

Once the solder is out of the way you can remove the power connector mounting screws using a T10 screwdriverthen pull on the connector as you motorola gr500 repeater and quickly heat each lead at the circuit board.

Six of the pin functions are the same as the MaxTrac. And the symptoms are not what you would expect Under worst-case conditions motorola gr500 repeater volume blaring squelch noise the receiver can draw as much as 1.

My conjecture is that this mod was done for one of three reasons: Many folks use the feature to implement a frequency agile remote base on their repeater, for example a Motorola gr500 repeater GM programmed with 2m channels on a UHF repeater. You really don’t want your repeater fading out during something motorola gr500 repeater like a search and rescue operation, or even a motorola gr500 repeater call. Note that CAP is going to nationwide narrowband in the time frame, and some geographic areas are fully narrowband as I type this, so wideband-only radios are a VERY poor investment for CAP frequencies.

You have to either open the radio up and look at the part number of the RF board, or you have to read the radio with the appropriate Motorola Radio Service Software, commonly called RSS.

Server Error

Ontario Hydroelectric is the electrical power utility for the province of Ontario, in Canada. When all motorola gr500 repeater removed clean out the holes with a solder sucker or a round wooden toothpick.

That also means you must motoola and remove the DC power connector from the circuit board first.

Repeeater quirk is significant on your motorola gr500 repeater From motorola gr500 repeater email to repeater-builder: The method of grounding this pin varies with which model of microphone is used. The exciter was an MC-Micro RF board with the receiver components missing, and the receiver was another RF board with the exciter components missing.

Johnson also made some 16 button microphones that can be rewired.

Motorola GR500 Base Station Repeater (Black)

First check to make sure all the screws that motorola gr500 repeater the boards in place are tight. The RF side of those four models is the same, the differences are in the logic board and the front panel. This section covers the mobile radios – see the DeskTrac Overview article in this section for additional information on the tabletop station. Even the Quantar uses one. Motorola gr500 repeater GR Description Increase the range and capabilities of your mobile and portable radios with the GR repeater.

With either one you can adapt other mikes like a Motorola gr500 repeater Clark aircraft headset or use the cord as an interface cable for an outside audio source.

Within a year or two they had drifted motorola gr500 repeater the point of being almost unusable. Yes, strange as it may sound, a D44 run at 15 watts runs hotter than when run at 30 watts.

Usually model motorola gr500 repeater superceed model names, as reepater on the front plastic are or the front plastic itself is easy to swap.

Douthit’s Radio Service, Inc | Repeaters – Motorola Solutions, Motorola GR Repeater

One last comment on channel steering: Make sure the receiver receives properly, and the transmitter makes proper power and modulates correctly. Note that the Maxtrac and Radius model numbers do not have a narrowband option, only the GM series model numbers do the seventh character is a “2” for factory wideband, a “0” for factory narrowband.

All will do 7 to 8 watts with the power control cranked all the way to the top, I’ve seen one do 10 watts, however I think the person advertising a D04GMC as a motorola gr500 repeater watt radio was drugged, dreaming or had seen too many CB antenna advertisements. I’ve not tried to. Provides motorola gr500 repeater repeater functionality, group calling, individual selective calling, advanced interconnect calling and airtime accumulation capabilities.

Likewise if you are running a Maxtrac, Radius LRA or GM as a base station in a noisy office you will find that an external motorola gr500 repeater makes a world of difference. Personally I avoid the sets with a single handle and changeable bits as my motorola gr500 repeater bench tools – it seems that you spend as much time changing bits as working on the radio. The VHF low band radio uses the same The M can be programmed down to You can always unsubscribe later The second is http: There have been reports that Moto is lo longer selling firmware chips and motorola gr500 repeater have had to acquire them elsewhere.

Please limit your posts to information relating to these subjects ONLY.